Industrial Routing Switchwww.westermo.com©Westermo Teleindustri ABUser Guide6641-22810RedFox Industrial Rack SERIESWeOS
106641-22810DescriptionThe RFIR (RedFox Industrial Rack) is a high performance layer 3 industrial Ethernet switch designed for high network traffic ap
116641-22810SpecificationDimension W x H x D 466 x 258 x 43 mm18,35 x 10,16 x 1,66"Weight 3.8 kgDegree of protection IP40 according to EN 60529Co
126641-22810Interface specificationsI/O USBConsole portSFP slot, 100/1000 Mbit/s FX or 10/10/1000 Mbit/s TX ports10/100 Mbit/s TX portsPower10/100/100
136641-22810PowerRated voltage AC models 100 to 240 VAC, 50-60 HzDC models 20 to 48 VDCOperating voltage AC models 90 to 264 VAC, 47-63 HzDC models
146641-22810USBElectrical specification USB 2.0 host interfaceData rate High speed 480mbit/sCircuit type SELVMaximum supply current 500 mAIsolation to
156641-22810Network portsRFIR-219-F4G-T7G DC and ACSlot 11 10/100/1000 Mbit/s, TX port2 10/100/1000 Mbit/s, TX port3 10/100/1000 Mbit/s, TX portSlot 2
166641-22810Ethernet TX Electrical specification IEEE std 802.3. 2005 EditionData rate 10 Mbit/s, 100 Mbit/s, 1000 Mbit/s, manual or autoDuplex Full o
176641-22810Position Direction* DescriptionRx In Receive portTx Out Transmit port* Direction relative this unit.10015263748SFP portsOptical/Electrica
186641-22810I/O connectionDO+DI-DI+DO-Product marking Direction DescriptionDigital in – Input Digital in –Digital in + Input Digital in +Status – Outp
196641-22810LED indicators Power/CPULED Status DescriptionON OFF Unit has no power.GREEN All OK, no alarm condition.RED Alarm condition, or until unit
26641-22810Legal informationThe contents of this document are provided “as is”. Except as required by applicable law, no warranties of any kind, eithe
206641-22810SFP TransceiversSee SFP Transceivers data sheet for supported SFP transceivers. Note: The unit supports Westermo labelled transceivers onl
216641-22810MountingWallmounting The unit can also be wallmounted in all directions. Use maximum Ø6,4 mm or 1/4"screws. Earth connection For corr
226641-22810Getting StartedThis product runs Westermo Operating System (WeOS) which provides several management tools that can be used for configurati
236641-22810Cable factory reset on RedFox Industrial RackIt is possible to set the unit to factory default settings by using a standard (straight) Eth
REV. D 6641-22810 2015-06 Westermo Teleindustri AB, Sweden – A Beijer Electronics Group CompanyFor complete contact information, please visit our
36641-22810SafetyBefore installation:Read this manual completely and gather all information on the unit. Make sure that you understand it fully. Che
46641-22810Note. Fibre Optic HandlingFibre optic equipment needs special treatment. It is very sensitive to dust and dirt. If the fibre will be discon
56641-22810Agency approvals and standards complianceArt.no Denomination Type Approval/compliance3641-40053641-40153641-40253641-4035RFIR-219-F4G-T7G-D
66641-22810Safety control drawingPositionDirection/ descriptionInput/Output valuesDO+ IO / Status + Uin = 60 VDC maxDO- IO / Status – Iin = 80 mA maxD
76641-228101000 Base-X1000 Base-T15678234Safety control drawingPosition Direction* / description Input/output valuesRx In / Receive portMax 5 dBmTx Ou
86641-22810Declaration of Conformity Westermo Teleindustri AB Declaration of conformity Org.nr/ Postadress/Postal address Tel. Telefax Pos
96641-22810Type tests and environmental conditionsPhenomena Test Description Test levelsESD EN 61000-4-2 Enclosure contact ± 6 kVEnclosure air ± 8 kV
Kommentare zu diesen Handbüchern