Westermo FD-80 Bedienungsanleitung

Fieldbus Adapter, Profibus DP slave – TCP/IPINSTALLATION MANUAL6630-2281www.westermo.seFD-80©Westermo Teleindustri AB • 2002 • REV. BGalvanicIsolation

10 6630-22816.4 ConfigurationThe device specific functionality and Profibus DP settings of FD-80 can be configured byusing FD-Tool (PC based software)

116630-2281Modify configurationConfigurations are defined per device type. see “Functional description”, chapter 7.FD-80 P Point to point (P)FD-80 A

12 6630-22816.4.5 Ethernet network configuration by using TelnetThe FD-80 is always available for configuration of the TCP/IP protocol settings, by us

136630-2281SETUP Port 0 (Serial)UART Setup Settings of the internal serial port TCP/IP control interface, internal-ly connected to the Profibus DP sla

14 6630-22816.4.6 Telnet configuration; Ethernet slave,point to point with continuously transfer modeContinuous transfer mode between two FD-80s by se

156630-2281Technical dataDevice type FD-80_PGSD-file FD-80_P.gsdProfibus DPInput data Up to 8 modules, max 64 word dataOutput data Up to 8 modules, m

16 6630-22817.1.1 Basic configurationSerial transfer > Transfer modePoint – point Select Transfer slave point to point mode, with serialconnection

176630-22817.1.1.1 Expert configurationSerial transfer > Expert parametersSerial interface Select the desired parameters of the internal interface

18 6630-2281Technical dataDevice type FD-80_AGSD-file FD-80_A.gsdProfibus DP Input data Up to 8 modules, max 64 word data (include 1 word status)Outpu

196630-22817.2.1 Basic configurationProfibus-DP >Profibus DP parametersProfibus DP Address Set this FD-10 Profibus DP address.Number of I/O Module

2 6630-2281Contents1. Introduction ...

20 6630-2281Word 15 High byte 8 7 Low byte 01 EN SDO – CNF RES – – – Transfer slave address, in range 1–642 Out word 1, high byte Out word 1, low by

216630-2281Word 15 High byte 8 7 Low byte 01 ST – DV – ACK TO – – – – – – – – – –2 In word 1, high byte In word 1, low byte–– ––– –64 In word 63, hi

22 6630-22817.2.2.3 Profibus DP communicationThis describes the required Profibus DP communication sequence, from a Profibus DPmaster unit to FD-80 (A

T03-0155 • 6630-2281 03.03 Mälartryck AB, Eskilstuna, SwedenWestermo Teleindustri AB • SE-640 40 Stora Sundby,SwedenPhone +46 16 42 80 00 Fax +46 16 4

36630-22811. IntroductionThe FD-80 Fieldbus Adapter Profibus DP slave, is a simple and cost effective way of connecting different Profibus DP networks

4 6630-22812. SafetyGeneral:Before using this unit,read the manual completely,and make sure that you understand it fully.Check that your application d

4. Specifications4.1 ConnectionseRated voltage 24V DC ± 20% (reverse polarity protected)Rated current 120 mARated frequency DCFuse NoConnection 1.5 m

6 6630-22814.2 InsulationPower to all other circuits 500 V RMS @ 50HzProfibus DP to Ethernet/Service 500 V RMS @ 50Hz4.3 Climatic environmentTemperatu

76630-22816. Installation6.1 Mounting /RemovalBefore mounting or removing the unit:Prevent damage to internal electronics from electrostatic discharge

8 6630-22816.2 ConnectionsProfibus DP interface9-pol D-sub, femaleEthernet/Service interface, 10Base-T, RJ-45 8-pin Modular JackPower interface 24 V D

96630-22816.3 Indicators6.3.1 LED indicatorsDIAG: LED 1 sec blinking No transfer of Profibus DP data throughEthernet.LED 1/2 sec blinking Transfer of