Westermo ODW-631 Bedienungsanleitung

©Westermo Teleindustri ABwww.westermo.comUser Guide6650-2243Industrial Converter Serial RS-485 to Fibre optic link Point-to-point applicationsODW-631

106650-2243STATUS C NO NC LED’s Switches CH 1 SFP Fibre transceiverTXRXInternal Electronics ODW- 631 COM COM +VA OVP +VB POWER T/R- T/R+RS -485 R-

116650-2243Point-to-point communication via fibre optical network The serial data is transferred via a fibre optic network between two ODW-631s. This

126650-2243Optical fibre link functionality and status indicationAt power on, all LED’s will be active during an initiation sequence followed by an au

136650-2243System delay in an optical networkSerial data transferred from one ODW-631 via an optical network to a second one, will be delayed due to t

146650-2243Status Port type Signal relay, changeover contactsRated voltage Up to 48 VDCOperating voltage Up to 60 VDCContact rating 500 mA @ 48 VDCCon

156650-2243FX (Fibre) SM-LC80 SM-LC40 SM-LC15 MM-LC2Fibre connector LC duplex LC duplex LC duplex LC duplexFibre type Singlemode 9/125 mmSinglemode 9/

166650-2243Location of Interface ports, LED’s and DIP-switchesODW-631Position Direction* Description Product marking1 In Common voltageCOM2 In Voltage

176650-2243Position Direction* Description Product marking1 In R+ (EIA RS-485 A’) R+2 In R– (EIA RS-485 B’) R–3 In/Out T+ (EIA RS-485 A) T/R+4 In/Out

186650-2243ConfigurationAll needed configurations and parameter settings are done by the DIP-switches, located under the top lid of the ODW-631.!DIP-s

196650-2243Factory settingsON 1 2 3 4 5 6 7 8S1ON 1 2 3 4 5 6 7 8S2S1 DIP-switchON 1 2 3 4 5 6 7 89 bits data formatON 1 2 3 4 5 6 7 810 b

26650-2243Legal informationThe contents of this document are provided “as is”. Except as required by applicable law, no warranties of any kind, either

206650-2243SW:1 SW:2Transmitter ONON 1 2 3 4 5 6 7 8ON 1 2 3 4 5 6 7 81.6 msON 1 2 3 4 5 6 7 8ON 1 2 3 4 5 6 7 8416 µsON 1 2 3 4 5 6 7

216650-2243RS-485 termination at system levelThe system should be installed in according to the RS-485 specification. A system should always form a b

226650-2243CoolingThis unit uses convection cooling. To avoid obstructing the air-flow around the unit, use the following spacing rules. Minimum spaci

236650-2243Configure the ODW-631. …S1: 2-wire RS-485. Data rate, asynchronous mode must be set by S1. …S2: Asynchronous mode or Synchronous mode. …S3

246650-2243HintsIf the distance is too long, it may be necessary to adjust the timing of the sender of the frame to allow acknowledgement of the recei

REV.B 6650-2243 2012-01 Westermo Teleindustri AB, Sweden – A Beijer Electronics Group CompanyWestermo Teleindustri AB • SE-640 40 Stora Sundby, S

36650-2243SafetyBefore installation:Read this manual completely and gather all information on the unit. Make sure that you understand it fully. Check

46650-2243Note. Fibre Optic HandlingFibre optic equipment requires careful handling as the fibre components are very sensitive to dust and dirt. If

56650-2243Declaration of Conformity, ODW-631 Westermo Teleindustri AB Declaration of conformity Org.nr/ Postadress/Postal address Tel. Tel

66650-2243

76650-2243

86650-2243Electromagnetic CompatibilityPhenomena Test Description LevelESD EN 61000-4-2 Enclosure contact ± 6 kVEnclosure air ± 8 kVRF field AM modul

96650-2243DescriptionThis ODW-631 is a fibre optic modem used for point-to-point applications. It acts as a converter between a serial port and a fibr